SKU: OT961-C105 Numero articolo: YP924 EAN: 4639867568390
Termini di ricerca: relais 5v, 5v relais, relay 5v, 5v relay, relais hoog, relais high, relay high, blauwe relais, relais blauw, relais 250v, relais 220v, relais voor arduino, arduino relais, relais breadboard
Dimensioni
Lunghezza: 3,3cm
Larghezza: 2,6cm
Altezza: 1,7cm
Ecco come collegare il Modulo relè 5v per Arduino a un Arduino UNO o ESP32, con uno sketch di esempio che puoi caricare subito.
Questo progetto mostra come controllare un modulo relè 5V con un Arduino UNO. Lo sketch commuta il relè ON e OFF ogni due secondi, stampando lo stato nel Serial Monitor. Sentirai un clic udibile del relè ogni volta che cambia stato.
English 
Nederlands 
Frans 
Deutsch 
Español 
Suomi 
Polski 
Dansk 
Ελληνικά 
Български 
Čeština 
Hrvatski 
Aileen/*
* ==================================================================
* Generated by Codey.online — https://www.codey.online
* ==================================================================
* Project : Control a 5V Relay with Arduino UNO
* Board : Arduino UNO (arduino:avr:uno)
* Parts : Relay Module 5V
* Libraries : none (built-in)
*
* Codey Online is an AI-powered browser IDE for Arduino and ESP32.
* Describe your project and Codey writes the code, draws the wiring
* diagram and uploads it to your board, straight from the browser.
* This code is free to use, modify and share, without warranty.
* ==================================================================
*/
// 5V Relay Module Example
const int RELAY_PIN = 7;
void setup() {
pinMode(RELAY_PIN, OUTPUT);
Serial.begin(115200);
Serial.println(F("Relay module demo started."));
}
void loop() {
// Turn relay ON
digitalWrite(RELAY_PIN, HIGH);
Serial.println(F("Relay: ON"));
delay(2000);
// Turn relay OFF
digitalWrite(RELAY_PIN, LOW);
Serial.println(F("Relay: OFF"));
delay(2000);
}Wiring diagram and example code generated by Codey.online — https://www.codey.online
Questo progetto mostra come controllare un modulo relè 5V usando un ESP32. Il relè si accende e si spegne ogni due secondi, mentre stampa il proprio stato nel Serial Monitor. Il relè è alimentato direttamente dal pin VIN dell’ESP32 (5V da USB) e attivato tramite GPIO 4.
/*
* ==================================================================
* Generated by Codey.online — https://www.codey.online
* ==================================================================
* Project : 5V Relay Control with ESP32
* Board : ESP32 DEVKIT V1 (esp32:esp32:esp32doit-devkit-v1)
* Parts : Relay Module 5V
* Libraries : none (built-in)
*
* Codey Online is an AI-powered browser IDE for Arduino and ESP32.
* Describe your project and Codey writes the code, draws the wiring
* diagram and uploads it to your board, straight from the browser.
* This code is free to use, modify and share, without warranty.
* ==================================================================
*/
// 5V Relay Control Example for ESP32
const int RELAY_PIN = 4;
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
digitalWrite(RELAY_PIN, LOW);
Serial.println("Relay control initialized.");
}
void loop() {
// Turn relay ON (Active HIGH for standard modules)
Serial.println("Relay: ON");
digitalWrite(RELAY_PIN, HIGH);
delay(2000);
// Turn relay OFF
Serial.println("Relay: OFF");
digitalWrite(RELAY_PIN, LOW);
delay(2000);
}Wiring diagram and example code generated by Codey.online — https://www.codey.online
